HP HP0-Y26 PDF download - Computers - Certification

Building a Complete HP ProCurve Mobility Solution HP0-Y26 Test

HP0-Y26

QUESTION: 1You have verified that an HP ProCurve Switch 3500yl is correctly configured for PIMdense mode. Theswitch's IGMP table shows active hosts that are members of multicastgroup 239.193.22.22. The multicastis in progress, and all hosts are receiving the content.However, the multicast group does not appear in the switch's PIM route table. What doesthis indicate about the 239.193.22.22 multicast group?

A. The switch is forwarding the multicast at Layer 2.B. Other multicast routers are configured for PIM sparse.C. The server and IGMP hosts are in different VLANs.D. The switch is Querier for the group.

Answer: A

QUESTION: 2You have enabled Dynamic ARP Protection on an HP ProCurve 5406zl switch. When isit necessary to define IPtoMAC address bindings?

A. when you must lock down the switch's IP addresses to its base MAC addressB. when you must specify clients connected to untrusted portsC. when you must identify devices that do not use DHCP, but have a static IP addressassignedD. when you must protect uplink ports that connect to other switches that do not supportDynamic ARP ProtectionE. when you must provide security to ports where different clients may connect atdifferent times

Answer: C

QUESTION: 3You must use the web management interface of an HP MSM710 Controller to perform amanual upgrade of the controller's software. In the management interface, which locationmust be specified as the source for the software file?

A. TFTP serverB. your workstationC. controller auxilary portD. your FTP server

Answer: B HP0-Y26

QUESTION: 4You must configure an HP ProCurve Switch 8212zl to be the Backup router for a VRIDassociated with VLAN 10. What must be true of the virtual IP address for the VRID onthis router?

A. It must be an address assigned to a multinetted interface.B. It must be an address that is not assigned to any interface on either router.C. It must match the Backup router's address for the VLAN 10 interface.D. It must match the Owner router's address for the VLAN 10 interface.

Answer: D

QUESTION: 5You must configure an HP ProCurve Switch 8212zl to be the Owner of a VRIDassociated with VLAN 10. What must be true of the virtual IP address for the VRID?

A. It must be an address on a multinetted interface.B. It must match the router's address for the VLAN 10 interface.C. It must match the address assigned to VLAN 10 on the Backup router.D. It must use a classful network mask.

Answer: B

QUESTION: 6On an HP ProCurve Switch 8212zl, which feature must be enabled before you can enableVRRP?

A. IP routingB. a dynamic routing protocolC. MSTPD. IP multicast

Answer: A

QUESTION: 7 HP0-Y26

A customer requires high levels of redundancy and availability for a critical businessnetwork that uses two HP ProCurve 8212zl switches in the core What is a potentialadvantage of deploying the BRRP on these switches?

A.It will enable the switches to learn redundant paths to remote networks.B.It will enable the switches to provide redundant default gateways to clients.C.It will enable the configuration of redundant gateways on VRRP-aware clients.D.It will enable the switches to provide redundant links to the distribution layer.

Answer: B

QUESTION: 8You must design an MSTP solution for a customer network that uses HP ProCurve5412zl switches in the core and 3500yl switches at the edge. All switches will belong to asingle MST region. How can you determine how many MST instances will be required toensure that all link are in a forwarding state for at least one VLAN?

A. Determine how many switches have identical VLAN congigurations.B. Count the number of redundant paths between the core and one edge switch.C. Count the switches at the network edge.D. Determine the total number of VLANs configured on the switches.

Answer: B

QUESTION: 9What is the effect of the following command entered at the CLI of an HP ProCurveSwitch 5412zl ?

A. The router will assume the role of AXBRB. The router will become eligible for election as DR.C. The router will assume the role of ABR.D. The router will summarize RIP routes is OSPF LSAs.

Answer: A

QUESTION: 10Click the Exhibit button. HP0-Y26

What is the role of the HP ProCurve Switch 3500yl in the OSPF fouting domain ?

A. ABR in areas 5 and 0B. ASBR in areas 5 and 0C. intemal router in area 5D. intemal router in area 0

Answer: A

QUESTION: 11Click the Exhibit button.

What is the role of the HP ProCurve Switch 3500yl in the OSPF routing domain?

A. ASBRB. virtual routerC. ABRD. internal router

Answer: D

QUESTION: 12You have enabled OSPF in global configuration context and in the VLAN 222 context ofan HP ProCurve Switch 8218zl ALL OSPF freas have been created and associated with

Original Resource :

Visit HP0-Y26 Link : HP0-Y26 Download PDF Link : HP0-Y26

access point vs router